Quantum 1200 Series DAT Autochanger Betriebsanweisung Seite 161
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-119
GLTSD Global Logging Target Save Disable. Always set to 0.
RLEC Report Log Exception Condition. Indicates whether the drive returns CHECK
CONDITION status with Sense Key set to UNIT ATTENTION (06h) when one of its
WRITE and READ error counters reaches a specified threshold.
When set to 0, indicates that the drive does not return UNIT ATTENTION when a
threshold has been met.
When set to 1, indicates that the drive returns UNIT ATTENTION when a threshold is
met.
Queue Algorithm
Modifier
Always set to 0.
QErr Queue Error. Always set to 0.
DQue Disable Queuing. Always set to 0.
TAS Task Aborted Status. Always set to 0. The drive does not return a status for tasks aborted
by the actions of other initiators.
RAC Report a Check. Always set to 0. The drive returns BUSY status rather than CHECK
CONDITION status during long busy conditions.
UA_Intlck_Ctrl Unit Attention Interlocks Control. Always set to 00b. The drive clears all UNIT
ATTENTION conditions when they are reported.
SWP Software Write Protect. Always set to 0.
Autoload Mode Indicates the action the drive is to take when tape medium is loaded. All values not listed
below are reserved.
Value Description
000b The medium is loaded for full access.
001b The medium is loaded for Enhanced Medium Auxiliary Memory
(EMAM) access only.
010b The medium is not loaded.
Busy Timeout
Period
Specifies the maximum time, in 100 msec increments, that the initiator allows the drive
to remain busy for unanticipated conditions that are not a routine part of commands from
the initiator. A value of 0000h is undefined. A value of FFFFh specifies an unlimited
busy timeout period.
Extended Self-
test Completion
Time
The drive does not support extended self-test. Always set to 0.
Table 4-67. Control Mode MODE SENSE Page — Field Descriptions (Continued)
Field Name Description
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Verwandte Produkte und Handbücher für Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Betriebsanweisung
(160 Seiten)
(160 Seiten)
Software Quantum SuperLoader Betriebsanweisung
(196 Seiten)
(196 Seiten)
Software Quantum Scalar i2000 Betriebsanweisung
(544 Seiten)
(544 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern