Quantum 3316 Bedienungsanleitung Seite 1

TM OWNER INSTALLATION AND USER MANUAL Series 3000 Models 3214, 3314, 3316 & 3414 Automatic Garage Door Opener

10 Step 12: Install Wireless Infrared Safety Sensors Wall Mounting Bracket (If Included) Select a mounting position 5 inches above the floor to cen

11 Step 15: Install Wired Infrared Safety Sensor Wall Mounting Brackets Use the following instructions if your opener is equipped with Wired Infra

12 Step 17: Install Wiring for Wired Infrared Safety Sensor Identify which side of the garage door opening (if any) the sun is “likely” to shine o

13 Step 19: Mount Wired Infrared Safety Sensors Attach the sending and receiv-ing units to the “U” brackets by inserting their tabs into their resp

14 Step 21: Wireless Wall Station Security Code Change and Programming Note: The following steps describe the process to change the Wireless Wall St

15 Step 22: Alignment of the Wireless Infrared Safety Sensors Use the following instructions if your opener is equipped with Wireless Infrared Safet

16 Step 23: Alignment of the Wired Infrared Safety Sensors Use the following instructions if your opener is equipped with Wired Infrared Safety Sens

17 Programming Transmitter to Power Head Unit Note: Do not press any button on the Transmitter until instructed 1. Press the PROGRAM Switch button

18 Step 27: Connecting Door Arm to Door Door Mounted Bracket Visually align cushion arm connecting hole with middle hole of door bracket by rotatin

19 Step 29: Setting Door Opening Travel Do not use adjustments to compensate for a poorly balanced door. This will interfere with the proper operati

2 Read These Important Safety Rules Before Proceeding IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury of death: READ

20 Step 31: Programming Wireless Keyless Entry (If Included) NOTE: To facilitate installation, program the Keyless Entry station to the opener befo

21 Adjustment # 1 Opening and Closing Force This garage door opener is built with a safety system that allows the door to reverse in the close

22 Adjustment # 2 Contact Obstruction Sensing (Closing Direction) The opener is designed to automatically reverse the door during closing travel whe

23 IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of severe injury of death: Before you proceed, please thoroughly read the safety rules on

24 HOW TO ACTIVATE THE OPENER Never let children operate or play with door controls. Keep remote control away from children. Use any of the foll

25 HOW TO OPERATE THE WIRELESS WALL STATION (If Included) Never let children operate or play with door controls. Keep remote control away from child

26 HOW TO OPERATE THE DOOR MANUALLY – Emergency Release Disconnect The door should be fully closed if possible, weak or broken springs could allow an

27 MAINTENANCE OF YOUR OPENER SYSTEM Test door opener monthly. The garage door MUST reverse on contact with a 1 inch high solid test ob-ject on the

28 TROUBLE SHOOTING SECTION SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Opener won’t work from wall button or radio control. No power to opener. Sho

29 Parts Breakdown Rail Assembly – All Models

3 Veuillez lire ces règles de sécurité importantes avant de commencer les travaux IMPORTANT —NOTICE D’INSTALLATION— AVERTISSEMENT –POUR REDUIRE LES

30 Parts Breakdown Power Head Assembly – All Models #. Part # Description Per Unit #. Part # Description # Per Unit 1. 157167 Frame 1 17.

31 QUANTUM ACCESSORIES Three Button mini/visor Transmitter Part#302083 Controls up to 6 doors or wireless ac-cessories. Includes visor clip. Wi

32 Questions? For quick answers and helpful advice, Call Toll Free 1-800-305-4349 LIMITED LIFETIME WARRANTY The Manufacturer warrants that the Quan

4 Automatic Garage Door Opener – For Residential Doors Only FEATURES 1. Open and Close Cycle Control: Allows garage door to be started and stopped

5 IMPORTANT PRE-ASSEMBLY CHECK If assembling a motor head unit from a factory sealed box skip this check. Every Power Head Unit is factory tested and

6 Step 1: Attaching Motor Power Head Unit to Rail Before assembly, align sprocket/coupling cogs to match notches of driver gear. Rotate the Motor Sp

7 Step 3: Attach Unit to Front Wall Bracket Raise the front end of the opener and attach it to the front wall bracket, using the ¼” x 4” hex head bol

8 Step 6: Mounting Door Bracket Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your garage door ma

9 Step 9: Installing Deluxe Wireless Wall Station (if included) Install all wall controls out of the reach of children and in a location where the do