Quantum SDLT 320 Betriebsanweisung Seite 73
- Seite / 102
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SDLT 220 and SDLT 320 Design & Integration Guide CHAPTER 6: SCSI and Controller Interface Specification
81-81148-01 March 2004 6-7
6.6 Power On Self Test
When power is applied to the tape system, the system performs a Power On Self
Test (POST). POST completes in approximately ten seconds. While POST is
running, the tape system responds BUSY to SCSI commands. The tape system
also responds to various SCSI messages during POST.
During this time, if a host tries to negotiate Synchronous or Wide transfers, the
tape system will negotiate to Asynchronous or Narrow. It may take longer than the
duration of POST for the drive to become ready.
6.7 SCSI Command Timeout
Table 6-5 shows the length of time a SCSI command “waits” for a response before
it times out.
Table 6-4. Indicator Pattern During POST
Stage What Can Be Observed
1 The LEDs light in a progressing pattern from left to right.
2
The red and yellow LEDs are extinguished and the green LED
flashes until POST completes.
3
If POST fails, the green and yellow LED will illuminate steadily
and the red LED will blink.
Table 6-5. SCSI Command Timeout Values
Command Timeout
ERASE 6 hours (overwrite entire tape)
INQUIRY 500 milliseconds
LOAD/UNLOAD 16 minutes
LOCATE 6 hours
LOG SELECT 500 milliseconds
LOG SENSE 500 milliseconds
MODE SELECT 500 milliseconds
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- Table of Contents 5
- 81-81148-01 March 2004 vii 7
- List of Tables 9
- List of Figures 11
- Introduction 13
- 1.2 Referenced Documents 14
- 1.3 Related Documents 14
- 1.4 Structure of this Manual 15
- 1.5 Conventions 16
- 1.6 For More Information 17
- 1.7 Reader Comments 17
- 1.8 Quantum Diagnostics Tools 18
- General Drive 19
- Specifications 19
- 2.2 SDLT Product Features 20
- 1 Amber LED 21
- 2 Green LED 21
- 3 Yellow LED 21
- 4 Eject Button 21
- 2.3 Dimensions and Tolerances 22
- 81-81148-01 March 2004 2-5 23
- 2-6 March 2004 81-81148-01 24
- 2.4 Physical Dimensions 25
- Orientation Looks Like This 26
- Typical (Top Side Up) 26
- Left Side Down 26
- Right Side Down 26
- 2.5 Reliability 27
- 2.5.4 Data Integrity 28
- Mechanism 29
- 2.6 Functional Specifications 30
- 81-81148-01 March 2004 2-13 31
- 2-14 March 2004 81-81148-01 32
- 2.6.5 Storage Capacity 33
- 2-16 March 2004 81-81148-01 34
- 81-81148-01 March 2004 2-17 35
- 2.7.2 Air Flow Requirements 36
- 2.7.3 Storage and Shipment 37
- 2.7.4 Altitude 37
- 2-20 March 2004 81-81148-01 38
- ≤ 20 lbs 39
- ≤ 50 lbs 39
- 2-22 March 2004 81-81148-01 40
- 81-81148-01 March 2004 2-23 41
- 2-24 March 2004 81-81148-01 42
- • Cleaning Requested 43
- • Cleaning Required 43
- • Cleaning Tape Expired 43
- SCSI Cleaning Error Reporting 44
- Figure 2-7. Front Panel LEDs 45
- 2-28 March 2004 81-81148-01 46
- Electrical Specifications 47
- 3-2 March 2004 81-81148-01 48
- 3.2 Power Supply Tolerances 49
- 3-4 March 2004 81-81148-01 50
- Thermal Specifications 51
- 4.2 Air Flow Measurements 52
- 81-81148-01 March 2004 4-3 53
- 4-4 March 2004 81-81148-01 54
- 81-81148-01 March 2004 4-5 55
- 4-6 March 2004 81-81148-01 56
- 81-81148-01 March 2004 4-7 57
- SDLT 320 58
- Embedded Bezel 59
- Library Bezel 60
- Regulatory Requirements 61
- 5.1.2 Safety Requirements 62
- 81-81148-01 March 2004 5-3 63
- 5.2.3 Conducted Emissions 64
- 5.2.4 Radiated Emissions 64
- Quantum tape drive products 65
- 5.3 Acoustic Noise Emissions 66
- SCSI and Controller 67
- Interface Specification 67
- 6.2 Setting the SCSI ID 68
- 81-81148-01 March 2004 6-3 69
- 6-4 March 2004 81-81148-01 70
- 6.3 Hardware (Connectors) 71
- 6.4 SCSI Stub Lengths 72
- 6.5 SCSI Cable Length 72
- 6.6 Power On Self Test 73
- 6.7 SCSI Command Timeout 73
- 6-8 March 2004 81-81148-01 74
- 6.8 SCSI and Power Connectors 75
- • Connector body: 51110-0850 76
- Figure 6-4. Loader Connector 76
- (Internal Version Shown) 76
- 81-81148-01 March 2004 6-11 77
- 6-12 March 2004 81-81148-01 78
- 81-81148-01 March 2004 6-13 79
- 6-14 March 2004 81-81148-01 80
- 81-81148-01 March 2004 6-15 81
- 6.10 Configuring the Drive 82
- Updating the Firmware 83
- 7.1.2 Making a FUP/CUP Tape 84
- 7.1.3 Using a CUP/FUP Tape 84
- 81-81148-01 March 2004 7-3 85
- Drive Interface 86
- • Updating the same revision 87
- 7-6 March 2004 81-81148-01 88
- Insertion and Extraction 89
- Guidelines 89
- 8.1.1 General Status Packet 90
- 8.1.2 Loading a Tape 91
- 8.1.3 Unloading a Tape 92
- Configuration) 93
- 81-81148-01 March 2004 8-7 95
- Insertion Depth 97
- Cartridge Insertion Force 97
- Insertion Velocity 97
- Debounce Time 98
- Initialization Time 98
- 81-81148-01 March 2004 8-11 99
- Eject Distance 100
- Cartridge Extraction Force 100
- Extraction Velocity 100
- 81-81148-01 A02 102
Verwandte Produkte und Handbücher für Tape Auto Loader & Bibliotheken Quantum SDLT 320
(294 Seiten)
(222 Seiten)
(34 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.910 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern