Quantum DPA Betriebsanweisung Seite 20
- Seite / 101
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Quick Start Installation Installing a Desktop CP 3100
21
Installing a Desktop CP 3100
Use the following procedure to get a desktop CP 3100 up and running. Print this page and check
each step as you complete it. If you need more information about a step, turn to the section refer
-
enced in the step.
❑
1.
Unpack the contents of your package, and check for damaged items.
See “Unpacking and Inspection” on page 23.
❑
2.
Obtain the additional items you need to install the CP 3100.
See “Items You Must Supply” on page 36.
❑
3.
Be sure the CP 3100’s SCSI ID is not being used by another device on the SCSI chain.
See “Reviewing the SCSI ID” on page 36.
❑
4.
Shut down the computer and disconnect the computer’s AC power cord.
See the manual that came with your computer.
❑
5.
Connect the CP 3100 to a host computer.
See “Connecting to a Host” on page 37.
❑
6.
If you have the CP3100D-160, connect it to an approved DDS-4 or DAT 72 tape drive.
See “Connecting to a Tape Drive” on page 37.
❑
7.
Terminate the SCSI chain appropriately for your configuration.
See “Terminating the SCSI Chain” on page 38.
❑
8.
Connect the CP 3100 to your LAN.
See “Connecting to the Network” on page 38.
❑
9.
Power-up the CP 3100.
See “Powering-up the Desktop CP 3100” on page 38.
❑
10.
If your operating system or backup software does not recognize the CP 3100, you may
need to install drivers. See “Installing the Driver” on page 39.
❑
11.
Register the CP 3100.
See “Registering the CP 3100” on page 39.
❑
12.
Perform the initial CP 3100 setup procedures:
• Log into RemoteAdmin.
See “Logging into RemoteAdmin” on page 44.
• Set the CP 3100 clock to the current date and time.
See “Setting the CP 3100’s Internal Clock” on page 46.
• Set a RemoteAdmin password.
See “Specifying a Password” on page 47.
• Specify the CP 3100 network settings.
See “Configuring Network Settings” on page 48.
• Configure the CP 3100 email settings.
See “Configuring Email Settings” on page 50.
❑
13.
Install your backup software application.
❑
14.
Verify your installation.
See “Verifying Your Installation” on page 53.
- CP 3100 D2D2T Solution 1
- Copyright and Trademarks 2
- Warnings 3
- Precautions 4
- FCC Notice 5
- Contents 6
- List of Figures 8
- List of Tables 10
- 1 Introduction 11
- Features and Benefits 12
- CP 3100 Configurations 12
- CP 3100 Theory of Operation 14
- Overview 14
- The Flow of Data 15
- 2. CP 3100 returns data 16
- 1. Host requests 16
- Using This Guide 17
- 2 Quick Start Installation 18
- Installing a Desktop CP 3100 20
- 3 Installing the CP 3100 22
- Handling Precautions 23
- Items You Must Supply 23
- Reviewing the SCSI ID 23
- Power Cord 25
- VHDC-1 converter 26
- VHDC-1 connector 26
- Terminator 27
- Ethernet connector 28
- Connecting Expansion Units 30
- Installing the Driver 30
- Figure 17. Information Box 33
- Registering the CP 3100 34
- How to Proceed 34
- Connecting to a Host 36
- Connecting to a Tape Drive 36
- Terminating the SCSI Chain 37
- Connecting to the Network 37
- 4 Initial Setup 43
- Figure 21. Welcome Page 44
- Specifying a Password 46
- Configuring Network Settings 47
- Configuring Email Settings 49
- Table 6. Email Settings Page 50
- Verifying Your Installation 52
- CP 3100 Operation 52
- Logging into RemoteAdmin 53
- Performing Basic Operations 56
- Viewing Device Properties 58
- Figure 30. Device Properties 59
- Viewing Pending Attentions 60
- Displaying Pop-up Information 64
- • Remove a virtual cartridge 69
- Viewing System Information 73
- Figure 37. System Info Page 74
- Table 14. System Info Page 74
- Updating the CP 3100 Firmware 75
- Viewing Device Inventories 76
- Viewing the System Log 79
- Viewing Messages 80
- 7 CP 3100 LEDs 82
- System LED 83
- Attention LED 83
- Virtual Tape LED 84
- Physical Tape LED 84
- Network Activity LED 84
- Using the Appropriate Media 85
- Handling Cartridges 86
- Applying Labels 86
- Loading a Cartridge 87
- Ejecting a Cartridge 87
- Write protected 88
- Write enabled 88
- Cleaning the Tape Path 89
- 9 Troubleshooting 90
- SCSI ID Problems 91
- SCSI Termination Problems 91
- CP 3100 Does Not Work 92
- Power On Self Test Fails 92
- Computer Does Not Boot 92
- Removing the Hard Disk 93
- 10 Recording Your Settings 95
- A CP 3100 Operation 96
- Archiving and Migrating 98
Verwandte Produkte und Handbücher für Vernetzung Quantum DPA
Vernetzung Quantum PX506 Installationshandbuch
(40 Seiten)
(40 Seiten)
Vernetzung Quantum QVNR Bedienungsanleitung
(91 Seiten)
(91 Seiten)
Vernetzung Quantum FC420 Betriebsanweisung
(26 Seiten)
(26 Seiten)
Vernetzung Quantum TC2201E Betriebsanweisung
(202 Seiten)
(202 Seiten)
Vernetzung Quantum TC2201 Betriebsanweisung
(164 Seiten)
(164 Seiten)
Vernetzung Quantum PX502 Betriebsanweisung
(14 Seiten)
(14 Seiten)
Vernetzung Quantum 560UF/L Bedienungsanleitung
(45 Seiten)
(45 Seiten)
Vernetzung Quantum DAT 160 Betriebsanweisung
(64 Seiten)
(64 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern