Quantum Scalar 100 Betriebsanweisung Seite 79
- Seite / 126
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Maintaining your Library 9-69
Scalar 100
3. Use Open/Close to open and close the picker fingers. Use Extend/Retract to extend and
retract the picker fingers.
The actions are performed in real time and the screen updates to reflect the current action.
4. When finished, select Cancel.
Exercising the Barcode Scanner
Use Scanner to instruct the barcode scanner to read the barcode information on the media
cartridge in front of it. Use this command in conjunction with Moving the Picker on page 7-50
.
Path: Main menu > More > Service > Library > Diags > Fingers > Scanner
To exercise the barcode scanner
1. From the Main menu, select More and then select Service. Select Library and then select
Diags. Select Fingers and then select Scanner.
2. Select Scan.
The barcode is read and the resulting barcode number is displayed at the bottom of the dialog.
If there is no tape cartridge in the slot, BAD READ is displayed.
Exercising the Picker Axes
Use Picker to manipulate the vertical and rotary axes of the library picker. You can exercise both
dimensions at once or a single dimension.
Path: Main menu > More > Service > Library > Diags > Picker
Moving the Picker in a Motion Pattern
Use Move to cycle the vertical and rotary axes of the picker in a motion pattern.
Path: Main menu > More > Service > Library > Diags > Picker > Move
To move the picker
1. From the Main menu, select More and then select Service. Select Library and then select
Diags. Select Picker and then select Move.
2. Using Up, Down, and Next, complete the following fields:
• Cycles to run — specifies the number of move cycles. Possible values are 0 to 9999.
• Use vertical — specifies whether or not to exercise the vertical axis during this test.
Possible values are Yes and No.
• Use horizontal — specifies whether or not to exercise the horizontal axis during this test.
Possible values are Yes and No.
3. With Use vertical or Use horizontal selected, press OK.
4. While the exercise is running, the status is displayed on the Operator Panel.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Verwandte Produkte und Handbücher für Tape Auto Loader & Bibliotheken Quantum Scalar 100
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern