Quantum Scalar 100 Betriebsanweisung Seite 92
- Seite / 126
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
11-82 6-00667-01 Rev B
Scalar 100
Configuring Network Parameters
You can reconfigure the hostname, IP address, subnet mask, and gateway address through the
RMU. This feature requires you to login to the RMU. See Logging into the RMU on page 11-81
for more information.
To configure the network parameters
1. Click the Configuration tab.
2. In the Network Configuration area, enter the new hostname, IP address, subnet mask, and
gateway address.
3. Click Submit and review your changes (indicated in red).
4. Enter your password and click Confirm to complete the procedure.
The new values are saved. Note that you may need to redirect your Web browser.
Configuring SNMP
Simple Network Management Protocol (SNMP) is a set of protocols used to manage nodes on an
IP network. You can configure the RMU to run a SNMP management application.
To configure SNMP
1. Click the Configuration tab.
2. In the SNMP Configuration area, do the following:
• To enable or disable the feature, select ON or OFF in the SNMP Enabled drop-down.
• To enable or disable SNMP alerts, select ON or OFF in the Alerts Enabled drop-down.
•In Manager, enter the SNMP server address.
•In Public Name, enter the name of the read-only SNMP community.
•In Private Name, enter the name of the read/write SNMP community.
3. Click Submit and review your changes (indicated in red).
4. Enter your password and click Confirm to complete the procedure.
The new values are saved. Note that you may need to redirect your Web browser.
5. You will be instructed to reboot the RMU. Click Done to reboot.
Downloading the SNMP MIB File
The SNMP Management Information Base (MIB) file will allow an SNMP management application
to understand the SNMP traps generated by the RMU. If you are running an SNMP management
application and need the library MIB, you can download it via the RMU.
To download the SNMP MIB file
1. Click SNMP MIB in the left pane of the RMU interface.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Verwandte Produkte und Handbücher für Tape Auto Loader & Bibliotheken Quantum Scalar 100
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern