Quantum DLT 4000 Handbuch Seite 242
- Seite / 300
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SCSI Commands
5-142 Quantum DLT 4000 Tape Drive
REQUEST SENSE Command (03h) (continued)
Table 5–68 Supported ASC / ASCQ in Hex (continued)
Sense Key ASC ASCQ Description
05h 1A 00 Parameter List Length Error
ILLEGAL REQUEST 20 00 Illegal Opcode
20 81 Illegal Command While In Recovery Mode
21 01 Invalid Element Address (Media Changer)
24 00 Invalid CDB Field
24 81 Invalid Mode on WRITE Buffer
24 82 Media in Drive
24 84 Insufficient Resources
24 86 Invalid Offset
24 87 Invalid Size
24 89 Image Data Over Limit
24 8B Image/Personality is Bad
24 8C Not Immediate Command
24 8D Bad Drive/Server Image EDC
24 8E Invalid Personality for Code Update (CUP)
24 8F Bad Controller Image EDC
25 00 Illegal LUN
26 00 Parameter List Error, Invalid Field
26 01 Parameter List Error, Parameter Not Supported
26 02 Parameter List Error, Parameter Value Invalid
30 00 Incompatible medium (cannot read medium)
39 00 Saving Parameters Not Supported
3B 0D Media Destination Element Full*
3B 0E Media Source Element Empty*
3D 00 Invalid Bits in ID Message
53 02 Media Removal Prevented
82 00 Not Allowed if not at BOT
06h 28 00 Not Ready To Ready Transition
UNIT ATTENTION 29 00 Reset Occurred
2A 01 Mode Parameters Changed
2A 02 Log Parameters Changed
3F 01 Microcode has been Changed
5B 01 Log Threshold Condition Met
07h 27 80 Hardware WRITE Protect
DATA PROTECTED 27 82 Data Safety WRITE Protect
08h 00 05 EOD Encountered
BLANK CHECK 08 00 LUN Communications Failure
01 LUN Communications Time-out
0Ah 0A 00 Error Log Overflow
80 Error Log Generated
* = Medium Changer specific command.
- DLT™4000 Tape Drive 1
- Product Manual 1
- TABLE OF CONTENTS 7
- REVISION HISTORY 19
- Revision History 20
- Quantum DLT 4000 Tape Drive 20
- ABOUT THIS MANUAL 21
- CONVENTIONS 23
- READER COMMENTS 23
- About This Manual 24
- Chapter 1 25
- Tabletop Version 1 26
- Tabletop Version 2 26
- 1.2 PRODUCT FEATURES 27
- 1.3 PRODUCT SPECIFICATIONS 27
- 1.3.2 Interface Type 28
- 1.3.3 Storage Capacity 28
- 1.3.4 Performance Data 28
- 1.3.6 Power Requirements 31
- 1.3.9 Reliability (Projected) 32
- Chapter 2 35
- HARDWARE IMPLEMENTATION 35
- 2.1.1 Safety Precautions 36
- 2.1.2 Handling 36
- 2.2 DRIVE SETUP 37
- Hardware Implementation 39
- SCSI ID Pushbutton 41
- 2.3 DRIVE INSTALLATION 42
- 2.4 DRIVE CONNECTIONS 44
- Pin Number Signal Name 48
- 1 +12 VDC 48
- 2 Ground (+12 V return) 48
- 3 Ground (+5 V return) 48
- 4 +5 VDC 48
- Table 2–5 LED Functionality 52
- 2.5.2 Selecting Density 56
- 2.6 POWER ON SELF TEST (POST) 58
- 2.7 TROUBLESHOOTING 60
- Chapter 3 63
- SCSI DESCRIPTION 63
- SCSI Description 64
- 3.3 SIGNAL STATES 66
- Table 3–2 Signal Sources 67
- 3.4 SCSI SIGNALS 68
- 3.4.2 Signal Bus Timing 69
- 3.5 SCSI BUS PHASES 72
- • DISCONNECT 73
- • COMMAND COMPLETE 73
- 3.5.3 SELECTION Phase 75
- The initiator: 76
- The drive: 76
- 3.5.4 RESELECTION Phase 77
- Table 3–6 Status Bytes 85
- 3.6 SCSI BUS CONDITIONS 86
- 3.6.2 Reset Condition 87
- 3.6.3 Queued Unit Attentions 88
- Chapter 4 89
- MESSAGES 89
- 4.2 SUPPORTED SCSI MESSAGES 93
- Messages 100
- Chapter 5 101
- SCSI COMMANDS 101
- SCSI Commands 102
- 5.1.1 SCSI Pointers 103
- 5.1.3 Status/Error Reporting 107
- 5.2 SCSI COMMAND DESCRIPTIONS 113
- 5.3 ERASE COMMAND (19H) 115
- 5.4 INQUIRY COMMAND (12H) 117
- 5.6 LOCATE COMMAND (2BH) 130
- 5.7 LOG SELECT COMMAND (4CH) 132
- 5.7.2 Operation of LOG SELECT 134
- 5.8 LOG SENSE COMMAND (4DH) 139
- • A page is not supported 142
- • The SP bit is set to 1 142
- • PPC bit is set to 1 142
- (continued) 146
- 0000h – 000Fh) 156
- 0000h, 0001h, or 0002h) 159
- 5.9.1 Mode Parameter List 163
- 5.10.3 MODE SENSE Mode Pages 199
- Data Format 215
- 5.12 READ COMMAND (08H) 217
- 5.14.2 Data Mode 224
- 5.14.3 Descriptor Mode 224
- • A hard reset occurs 245
- 5.23 SPACE COMMAND (11H) 252
- 5.25 VERIFY COMMAND (13H) 255
- 5.26 WRITE COMMAND (0AH) 257
- 5.27.2 Write Data Mode (010b) 260
- Appendix A 265
- INFORMATION 265
- Appendix B 269
- B.2.1 POST Failure Packets 270
- B.2.2 Event Log Packets 271
- Appendix C 275
- UPDATING THE FIRMWARE 275
- • Examines the data 277
- Appendix D 281
- THE TAPE CARTRIDGE 281
- Reel Lock Opening 284
- Spring-Loaded Hub 285
- WRITE-PROTECTION 288
- D.4 LOADING A TAPE CARTRIDGE 290
- *81-60043-04 A01* 300
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum DLT 4000
(1 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.198 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern