Quantum L500 Betriebsanweisung Seite 69
- Seite / 120
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 3 Basic Library Operations
Mode
Quantum|ATL PowerStor L500 Series Tape Library User’s Guide 53
Sequential
Circ
Primarily designed for testing purposes, this command
instructs the tape library to behave as an autoloader.
Cartridges are loaded sequentially from the lowest magazine
address and the lowest loaded slot position in that magazine.
The loading and unloading of cartridges sequentially
progresses to the last cartridge and then the tape library
restarts the sequential loading sequence again from the first
available slot.
This command works in conjunction with the
Autoload
Cart
command.
Note:
The Sequential mode is functional only if the library is
configured with a single drive.
Not
Selected
Selected
Autoload
Cart
This command functions only in conjunction with
Sequential
or
Sequential Circ
. Upon issuance of this command, the
library starts loading cartridges following an open/close door
operation per
Sequential
or
Sequential Circular
mode.
The library must be either in the
Sequential
or
Sequential
Circ
mode for
Autoload Cart
mode to be functional.
N
Y
Enable
Barcode
(optional)
When enabled, the optional bar code reader scans the
cartridge bar code labels on power up and when the doors are
closed. The bar code labels are read via the OCP Status display
or a SCSI
Read Element
status command.
To use, (a) press
ENTER
to Enable Bar Code: Y, and (b) make
sure doors are closed.
N
Y
AutoClean
(optional)
When enabled, the library automatically cleans drives when
required.
The time that a SCSI
Move Media
command takes to
complete increases from approximately 20 seconds to 60
seconds because the library must wait until calibration is
complete. If cleaning is required, the typical time increases to a
maximum of 10 minutes while the drive is cleaned.
To use, (a) load the cleaning tape in slot 13, (b) press ENTER to
enable
AutoClean: Y
.
N
Y
Option Description Message
- User’s Guide 1
- Contents 3
- Audience 11
- Document 11
- Organization 11
- Notational 12
- Conventions 12
- Contacts 14
- Technical Publications 14
- World Wide Web 14
- Library Description 17
- Full magazine 18
- Access door 18
- Operator Control 18
- Panel (OCP) 18
- Element 20
- Numbering 20
- Convention 20
- Features 21
- Library Components 22
- Back Panel 23
- Bar Code Reader 24
- (Optional) 24
- Cartridge Handling 24
- Mechanism (CHM) 24
- Tape Drives 25
- Drive Mounting 26
- Description 26
- Supported Tape Cartridges 27
- Dual 7-Cartridge 28
- Magazines 28
- Chapter 2 31
- Floor Space 32
- Receiving the Library 34
- Unpacking the Library 35
- Accessories 36
- The library is now unpacked 37
- Connecting the Tape Library 38
- Configuring the Tape Library 41
- Operating the Tape Library 43
- Inserting a 44
- Cartridge 44
- Write-protect switch 46
- Metal tab 46
- Back of magazine 46
- Front of magazine 47
- Using the Cleaning 48
- Basic Library Operations 49
- OCP Functions 50
- Table 3 OCP LCD 51
- Menu Structure 51
- Table 4 OCP Button 54
- Descriptions 54
- Table 5 Status 56
- Eject/Unlock 58
- Magazine Removal 60
- Installing a 61
- Magazine 61
- Loaded magazine 62
- Loading a Cartridge 63
- Setting a SCSI ID 67
- Table 8 Mode 68
- Sequential 69
- Sequential Circ 69
- Information 71
- Code Update 72
- Table 11 Test Options 74
- SCSI Interface 75
- Chapter 4 SCSI Interface 76
- General SCSI Bus Operation 76
- Attention Signal 78
- Response 78
- Status Phase 78
- Bus Free 79
- Bus Parity Errors 79
- Troubleshooting Guidelines 81
- Avoiding Basic Problems 82
- Operation Failure 83
- Power Problems 83
- Library Specifications 85
- provides 87
- Table 16 88
- Table 16 Shock 89
- Specifications 89
- (Operating) 89
- Table 17 Vibration 90
- Specifications (Non 90
- Table 18 Shock 91
- Table 21 ESD Failure 93
- Level Limits 93
- Acoustic Noise 94
- Emissions 94
- Table 22 Nominal 94
- Reliability Factors 95
- OCP Error Messages and Error 97
- Definitions 97
- Table 25 Library 100
- Error Definitions 100
- Regulatory Statements 109
- ICES-003 Issue 2 110
- Glossary 113
- S Scalability 115
- Self-cleaning head 115
- T Tape drive 115
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum L500
Bandlaufwerke Quantum DLT4500 Bedienungsanleitung
(360 Seiten)
(360 Seiten)
Bandlaufwerke Quantum DLT-V4 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
Bandlaufwerke Quantum Scalar i6000 Betriebsanweisung
(106 Seiten)
(106 Seiten)
Bandlaufwerke Quantum TC-L32AX-EY Datenblatt
(2 Seiten)
(2 Seiten)
Bandlaufwerke Quantum TC-L32BX-EY Betriebsanweisung
(109 Seiten)
(109 Seiten)
Bandlaufwerke Quantum DLT-V4 Handbuch
(28 Seiten)
(28 Seiten)
Bandlaufwerke Quantum DLT 7 Handbuch
(177 Seiten)
(177 Seiten)
Bandlaufwerke Quantum DLT 8000 Handbuch
(408 Seiten)
(408 Seiten)
Bandlaufwerke Quantum LTO-6 Betriebsanweisung
(38 Seiten)
(38 Seiten)
Bandlaufwerke Quantum DLT 2500 Wartungshandbuch
(114 Seiten)
(114 Seiten)
Bandlaufwerke Quantum 3U Bedienungsanleitung
(16 Seiten)
(16 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern