Quantum DLT 8000 Handbuch Seite 133
- Seite / 408
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Messages
Quantum DLT 8000 Tape System 4-3
Table 4–2 Supported Messages
Message Message Code Direction
ABORT 06h Out
BUS DEVICE RESET 0Ch Out
COMMAND COMPLETE 00h In
DISCONNECT 04h In Out
EXTENDED MESSAGE (SDTR and wide
Data Transfer Request)
*
01h In Out
IDENTIFY 80h – FFh In Out
IGNORE WIDE RESIDUE 23h In
INITIATOR DETECTED ERROR 05h Out
LINKED COMMAND COMPLETE 0Ah In
LINKED COMMAND COMPLETE (with
flag)
0Bh In
MESSAGE PARITY ERROR 09h Out
MESSAGE REJECT 07h In
NO OPERATION 08h Out
RESTORE POINTERS 03h In
SAVE DATA POINTER 02h In
WIDE DATA TRANSFER REQUEST
*
03h In Out
*
Extended messages (Figure 4–1).
Two-byte messages consist of two consecutive bytes. The value of the first byte, as
defined in Table 4–1, determines which message is to be transmitted. The second byte is
a parameter byte that is used as defined in the message description.
A value of 1 in the first byte indicates the beginning of a multiple-byte extended
message. The minimum number of bytes sent for an extended message is three. The
extended message format is shown in Figure 4–1 and the data fields are described in
Table 4–3.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum DLT 8000
Bandlaufwerke Quantum LTO-6 Betriebsanweisung
(38 Seiten)
(38 Seiten)
Bandlaufwerke Quantum DLT 2500 Wartungshandbuch
(114 Seiten)
(114 Seiten)
Bandlaufwerke Quantum 3U Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Bandlaufwerke Quantum DLT 8000 Betriebsanweisung
(69 Seiten)
(69 Seiten)
Bandlaufwerke Quantum LTO 4 Betriebsanweisung
(98 Seiten)
(98 Seiten)
Bandlaufwerke Quantum DLT 7000 Handbuch
(312 Seiten)
(312 Seiten)
Bandlaufwerke Quantum DLT 2500 Handbuch
(12 Seiten)
(12 Seiten)
Bandlaufwerke Quantum DLT 4000 Handbuch
(300 Seiten)
(300 Seiten)
Bandlaufwerke Quantum LTO-2 Spezifikationen
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern