Quantum DLT 8000 Handbuch Seite 84
- Seite / 408
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring, Installing, and Operating the Tape System
2-30 Quantum DLT 8000 Tape System
2.4.5 Unloading a Cartridge
NOTE
Because this section of the manual includes descriptions of the states of
indicators on the tape system, it may be useful to review sections of this chapter
that describe tape system indicators, their states, and meanings of states.
Follow the steps below the first CAUTION notice to unload a tape cartridge.
CAUTION
Always remove the tape cartridge from the tape system BEFORE turning off host
power. Failure to remove a tape cartridge may result in cartridge and/or tape
system damage.
When you remove a tape cartridge from the system, return the cartridge to its
plastic case to protect the cartridge from damage.
1. Press the Unload button (or issue an appropriate system software command). The
yellow Tape in Use indicator blinks as the tape rewinds.
CAUTION
Do NOT rush removal of the tape cartridge: premature removal can cause tape
leader failure. Wait until the Operate Handle indicator illuminates a steady green.
Delay removing the tape cartridge for one or two seconds to ensure that the tape
leader of the cartridge is in a safe position for cartridge removal.
2. When the green Operate Handle indicator illuminates steadily, lift the tape system
cartridge Insert/Release handle to its open position to eject the cartridge.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum DLT 8000
Bandlaufwerke Quantum LTO-6 Betriebsanweisung
(38 Seiten)
(38 Seiten)
Bandlaufwerke Quantum DLT 2500 Wartungshandbuch
(114 Seiten)
(114 Seiten)
Bandlaufwerke Quantum 3U Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Bandlaufwerke Quantum DLT 8000 Betriebsanweisung
(69 Seiten)
(69 Seiten)
Bandlaufwerke Quantum LTO 4 Betriebsanweisung
(98 Seiten)
(98 Seiten)
Bandlaufwerke Quantum DLT 7000 Handbuch
(312 Seiten)
(312 Seiten)
Bandlaufwerke Quantum DLT 2500 Handbuch
(12 Seiten)
(12 Seiten)
Bandlaufwerke Quantum DLT 4000 Handbuch
(300 Seiten)
(300 Seiten)
Bandlaufwerke Quantum LTO-2 Spezifikationen
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern