Quantum DLT 8000 Handbuch Seite 373
- Seite / 408
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Quantum DLT 8000 Tape System A-1
Appendix A
DEFINITION OF VENDOR UNIQUE SENSE DATA
INFORMATION
This appendix lists the internal status codes with their descriptions.
The internal status code is located at byte offset 18 of the REQUEST SENSE data and
may be available for certain types of failures.
NOTE
Byte 18 of the REQUEST SENSE data has two formats: a byte code and a bit flags
format. The bit flags format is used when there is no internal status code to report
and can be quickly distinguished by checking to see if bit 7 of byte 18 is set to 1.
Table A–1 Internal Status Codes
Decimal Hexadecimal Description
0 0 No Meaning
1 1 Reed-Solomon Error Correction Code Recovery
2 2 READ or WRITE Block Retry (Soft Retry)
3 3 REPOSITION Command Aborted
4 4 Controller Has Stopped Reading
5 5 No Control or Data Buffers Available
6 6 Target Delivered in Read Ahead
7 7 Logical EOT Encountered, 2 Filemarks
8 8 Command Connection Dropped
9 9 Cleared from Queue
10 0A Missing Data Block – READ only
11 0B Gap Within Object (Missing Block in Record)
12 0C Record on Tape Larger Than Requested
13 0D Compare Error
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum DLT 8000
Bandlaufwerke Quantum LTO-6 Betriebsanweisung
(38 Seiten)
(38 Seiten)
Bandlaufwerke Quantum DLT 2500 Wartungshandbuch
(114 Seiten)
(114 Seiten)
Bandlaufwerke Quantum 3U Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Bandlaufwerke Quantum DLT 8000 Betriebsanweisung
(69 Seiten)
(69 Seiten)
Bandlaufwerke Quantum LTO 4 Betriebsanweisung
(98 Seiten)
(98 Seiten)
Bandlaufwerke Quantum DLT 7000 Handbuch
(312 Seiten)
(312 Seiten)
Bandlaufwerke Quantum DLT 2500 Handbuch
(12 Seiten)
(12 Seiten)
Bandlaufwerke Quantum DLT 4000 Handbuch
(300 Seiten)
(300 Seiten)
Bandlaufwerke Quantum LTO-2 Spezifikationen
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern