Quantum LTO 2U Betriebsanleitung Seite 234
- Seite / 264
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
A-2
SCSI REFERENCE 1014826
CHAPTER A—ERROR CODES
Ta b l e A - 1 lists library LCD error messages in alphabetical order.
If the corrective action in the table:
Refers you to the Product Manual for instructions (“See the Product
Manual”), go to www.tandbergdata.com.
Instructs you to reset the library or tape drive, go to “Resetting the library
and Tape Drive” on page 3-4 for instructions.
Does not correct the error, contact Tandberg Data Technical Support at
www.tandbergdata.com or your service provider.
Table A-1 Library LCD error messages
Error Message Description Corrective Action
Auto Cleaning The tape drive is performing
an automatic cleaning of the
tape drive using the cleaning
cartridge in the fixed
cleaning cell.
No action necessary.
Bad Cleaning Tape The tape drive has
determined that the
cleaning cartridge is not the
proper type for this tape
drive.
Replace the cleaning cartridge with one that is
compatible with this tape drive.
Use only LTO cleaning cartridges with LTO tape
drives.
Bad Configuration Configuration of drives does
not match drives found in
library.
1. Verify that the tape drive settings in the “Drive
configuration” menu match the type of
drive(s) installed. See the Product Manual.
2. Check the ADI interface cabling and
configuration.
3. Verify that the tape drive is operating
correctly.
Bad Download An error occurred during a
firmware upload to the
library.
The data downloaded for
the code update is incorrect.
1. Verify that you loaded the correct code. Do
not load firmware from one model of library
or library into another.
2. Reset the library and reload the correct
firmware.
If the error persists, contact Tandberg Data
Technical Support or your service provider.
Bootblock An error occurred during
firmware programing of the
library.
1. Verify that you loaded the correct code. Do
not load firmware from one model of library
or library into another.
2. Reset the library and reload the firmware.
If the error persists, contact Tandberg Data
Technical Support or your service provider.
- EFERENCE 1014826 2
- ONTACTING 3
- ANDBERG DATA 3
- ORPORATION 3
- Contents 5
- SCSI REFERENCE 1014826 10
- ABOUT THIS MANUAL 17
- PRODUCT OVERVIEW 19
- 1.1.2 BACK PANEL COMPONENTS 20
- AGNUM 448 EMULATION MODES 24
- OVERVIEW OF THE LIBRARY 25
- SCSI DEVICE 25
- 2.1.1 ELEMENT TYPES 27
- 2.1.2 ELEMENT ADDRESSES 27
- Magnum 448 Element Addresses 29
- ELATIONSHIP TO THE SCSI BUS 31
- 2.2 SCSI COMMAND PROTOCOL 32
- OMMAND PROTOCOL 33
- 2.2.2 SCSI COMMAND FORMAT 34
- 2.2.3 COMMAND STATUS 35
- 2.2.4 COMMAND FORMAT ERRORS 36
- IMPLEMENTING SCSI 39
- OPERATIONS 39
- Disabling Sequential Mode 41
- Setting the Restart Option 41
- Setting the Loop Option 42
- Important 42
- ETTING ELEMENT ADDRESSES 43
- Element Addresses 45
- Element Occupied Status 46
- Bar Code Label Information 47
- 3.5 MOVING CARTRIDGES 48
- 3.7 PERFORMING DIAGNOSTICS 49
- Home Screen 50
- INITIALIZE ELEMENT 51
- STATUS (07h) 51
- 4.4 COMMAND STATUS 53
- STATUS WITH RANGE (37h) 55
- 5.4 COMMAND STATUS 58
- INQUIRY (12h) 59
- 6.3 WHAT THE LIBRARY RETURNS 60
- TANDARD INQUIRY DATA PAGE 61
- CODE 00h) 66
- Page Code – Byte 01 68
- Page Length – Byte 03 68
- 6.4 COMMAND STATUS 73
- LOG SELECT (4Ch) 75
- 7.3 COMMAND STATUS 76
- LOG SENSE (4Dh) 77
- 8.3 WHAT THE LIBRARY RETURNS 81
- 8.3.1 LOG PARAMETER FORMAT 82
- Parameter Length – Byte 03 83
- Parameter Value – Byte 04 90
- Command – Byte 04 91
- Fault Symptom Code – Byte 05 92
- Command Interface – Byte 06 93
- 8.4 COMMAND STATUS 94
- CHAPTER 8—LOG SENSE (4Dh) 96
- MODE SELECT (15h) 97
- 9.2.1 PARAMETER LIST HEADER 99
- Assigning Element Addresses 100
- ! Important 101
- HAT YOU SEND TO THE LIBRARY 103
- Page Length – Byte 01 104
- MaxStor – Byte 4, Bit 7 105
- Parameter Length – Byte 01 108
- Write Line 1 – Byte 02, Bit 3 108
- FixEnbl – Byte 02, Bit 0 109
- Auto – Byte 02, Bit 1 109
- 9.3 COMMAND STATUS 110
- MODE SENSE (1Ah) 113
- 10.3 WHAT THE LIBRARY RETURNS 115
- Mode Data Length – Byte 00 116
- HAT THE LIBRARY RETURNS 117
- CODE 1Eh) 119
- 10.4 COMMAND STATUS 130
- Check Condition 131
- CHAPTER 10—MODE SENSE (1Ah) 132
- MOVE MEDIUM (A5h) 133
- 11.4 COMMAND STATUS 137
- POSITION TO ELEMENT 139
- 12.3 COMMAND STATUS 140
- OMMAND STATUS 141
- PREVENT/ALLOW MEDIUM 143
- REMOVAL (1Eh) 143
- 13.3 COMMAND STATUS 144
- READ BUFFER (3Ch) 145
- 14.5 COMMAND STATUS 148
- CHAPTER 14—READ BUFFER (3Ch) 150
- READ ELEMENT STATUS 151
- 15.3 WHAT THE LIBRARY RETURNS 153
- 15.3.1 ELEMENT STATUS HEADER 154
- 15.3.2 ELEMENT STATUS PAGE 154
- Element Type Code – Byte 00 155
- PVolTag – Byte 01, Bit 7 155
- AVolTag – Byte 01, Bit 6 155
- 15.3.3 ELEMENT DESCRIPTORS 156
- Except – Byte 02, Bit 2 157
- TORAGE ELEMENT DESCRIPTOR 159
- Access – Byte 02, Bit 3 160
- Full – Byte 02, Bit 0 160
- SValid – Byte 09, Bit 7 161
- Invert – Byte 09, Bit 6 161
- 15.4 COMMAND STATUS 170
- RECEIVE DIAGNOSTIC 171
- RESULTS (1Ch) 171
- 16.3 WHAT THE LIBRARY RETURNS 172
- Bytes 02 and 03 – Page Length 173
- Page Code – Byte 00 173
- Page Length – Bytes 02 and 03 173
- Supported Log Pages – Byte 04 173
- Self Test – Byte 27 174
- 16.4 COMMAND STATUS 175
- RELEASE (17h OR 57h) 177
- 17.1 ABOUT THIS COMMAND 178
- 17.3 COMMAND STATUS 179
- REQUEST SENSE (03h) 181
- 18.3 WHAT THE LIBRARY RETURNS 183
- 18.4 COMMAND STATUS 186
- REQUEST VOLUME 187
- ELEMENT ADDRESS (B5h) 187
- 19.1 ABOUT THIS COMMAND 188
- 19.3 WHAT THE LIBRARY RETURNS 190
- 19.3.2 ELEMENT STATUS PAGE 191
- 19.3.3 ELEMENT DESCRIPTORS 192
- 19.4 COMMAND STATUS 204
- Reservation Conflict 205
- RESERVE (16h OR 56h) 207
- 20.1 ABOUT THIS COMMAND 208
- 20.3 COMMAND STATUS 209
- REZERO UNIT (01h) 211
- SEND DIAGNOSTIC (1Dh) 213
- DDITIONAL DIAGNOSTIC DATA 215
- ELF TEST PAGE (PAGE CODE F0h) 216
- 22.4 COMMAND STATUS 217
- SEND VOLUME TAG (B6h) 219
- ARAMETER LIST 221
- 23.4 COMMAND STATUS 222
- TEST UNIT READY (00h) 225
- WRITE BUFFER (3Bh) 227
- 25.4 COMMAND STATUS 230
- CHAPTER 25—WRITE BUFFER (3Bh) 232
- ERROR CODES 233
- IBRARY “FATAL” ERROR MESSAGES 243
- A.3 ERROR RECOVERY PROCEDURES 258
Verwandte Produkte und Handbücher für Leere Datenbänder Quantum LTO 2U
(82 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern