Quantum 1200 Series DAT Autochanger Betriebsanweisung Seite 190
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
PERSISTENT RESERVE OUT Command (5Fh) SDLT 600 SCSI Interface Guide
4-148 January 2005 81-81200-02 REV A01
The following table presents the definitions of the available Type values from the Type field of the
PERSISTENT RESERVE OUT Read Reservations parameters. Each of the codes provides handling
instructions for READ operations, for WRITE operations, and for subsequent attempts to establish
persistent reservations (referred to as “Additional Reservations Allowed” in the table).
Table 4-84. PERSISTENT RESERVE OUT Type Codes
Code Name Description
0h Obsolete ---
1h WRITE
Exclusive
READS: Shared. Any application client on any initiator may
execute commands that perform transfers from the tape medium
to the initiator.
WRITES: Exclusive. Any command from any initiator other than
the initiator that holds the persistent reservation that attempts a
transfer to the tape medium results in a reservation conflict.
2h Obsolete ---
3h Exclusive
Access
READS: Exclusive. Any command from any initiator other than
the initiator holding the persistent reservation that attempts a
transfer from the tape medium results in a reservation conflict.
WRITES: Exclusive. Any command from any initiator other than
the initiator holding the persistent reservation that attempts a
transfer to the tape medium results in a reservation conflict.
4h Obsolete ---
5h WRITE
Exclusive
Registrants Only
READS: Shared. Any application client on any initiator may
execute commands that perform transfers from the tape medium
to the initiator.
WRITES: Exclusive. Any command from an initiator that has not
previously performed a Register service action with the drive that
attempts a transfer to the tape medium results in a reservation
conflict.
6h Exclusive
Access
Registrants Only
READS: Exclusive. Any command from an initiator that has not
previously performed a Register service action with the drive that
attempts a transfer from the tape medium results in a reservation
conflict.
WRITES: Exclusive. Any command from an initiator that has not
previously performed a Register service action with the drive that
attempts a transfer to the tape medium results in a reservation
conflict.
7h -
Fh
Reserved Not applicable
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Verwandte Produkte und Handbücher für Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Betriebsanweisung
(160 Seiten)
(160 Seiten)
Software Quantum SuperLoader Betriebsanweisung
(196 Seiten)
(196 Seiten)
Software Quantum Scalar i2000 Betriebsanweisung
(544 Seiten)
(544 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern