Quantum 1200 Series DAT Autochanger Betriebsanweisung Seite 213
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-171
Previous
Amount of
Data Read
Indicates the amount of data physically read from the medium during the
previous load of the medium. This value is expressed in increments of 1,048,576
bytes; that is, a value of 1 means 1,048,576 bytes, 2 means 2,097,152 bytes, and
so on.
Previous
Read
Retries
Count
Indicates the number of times the drive performed a Read retry during the
previous load of the medium.
Total
Amount of
Data
Written
Indicates the amount of data physically written to the medium since the last
medium format. This value is expressed in increments of 1,048,576 bytes; that is,
a value of 1 means 1,048,576 bytes, 2 means 2,097,152 bytes, and so on.
Total Write
Retries
Count
Indicates the total number of times the drive performed a Write retry since the last
medium format.
Total
Amount of
Data Read
Indicates the amount of data physically read from the medium since the last
medium format. This value is expressed in increments of 1,048,576 bytes; that is,
a value of 1 means 1,048,576 bytes, 2 means 2,097,152 bytes, and so on.
Total Read
Retries
Count
Indicates the number of times the drive performed a Read retry since the last
medium format.
Load
Count
Indicates the number of loads since the last medium format. This count
accumulates over the life of the medium but it is reset to 0 after a medium format.
Total
Change
Partition
Count
Indicates the number of times that switches between partitions have been
performed on the medium. Must be set to 0. Super DLTtape media comprises a
single volume.
Total
Partition
Initialize
Count
Indicates number of times that any of the partitions on the medium have been
erased. This count accumulates over the life of the medium but it is reset to 0 after
a medium format.
Table 4-100. MEDIUM USAGE HISTORY Attribute Parameter Data —
Field Descriptions (Continued)
Field
Name
Description
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Verwandte Produkte und Handbücher für Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Betriebsanweisung
(160 Seiten)
(160 Seiten)
Software Quantum SuperLoader Betriebsanweisung
(196 Seiten)
(196 Seiten)
Software Quantum Scalar i2000 Betriebsanweisung
(544 Seiten)
(544 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern