Quantum 1200 Series DAT Autochanger Betriebsanweisung Seite 97
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-55
Table 4-33. TapeAlert Flags, Severity Levels, and Meanings
Flag
Severity
Level
1
Meaning
1 Read Warning Warning Problems reading data. There is no loss of data, but the
tape drive’s performance is reduced.
2 Write Warning Warning Problems writing data. There is no loss of data, but the
capacity of the tape is reduced.
3 Hard Error Warning An error occurred during a read or write operation that
the drive cannot correct: the operation has stopped.
4 Media Critical Your data is at risk. Copy all important data from this
data cartridge. Do not use the data cartridge again.
Restart the operation using a different data cartridge.
5 Read Failure Critical The data cartridge or the tape drive is damaged.
Contact a service representative.
6 Write Failure Critical The tape medium is faulty or the drive is damaged.
Test the drive using a known-good data cartridge. If
the problem persists, contact a service representative.
7 Media Life Warning The data cartridge has reached the end of its useful
life. Copy all important data to another data cartridge
and discard the old data cartridge.
9 Write Protect Critical The data cartridge is write-protected. Set the write-
protection switch to enable writing or use a different
data cartridge.
10 No Removal Informational The drive is busy and the data cartridge cannot be
ejected. Wait for the operation to complete before
attempting to eject the data cartridge.
11 Cleaning
Media
Informational The data cartridge in the drive is a cleaning cartridge.
For normal drive data-related operations, replace the
cleaning cartridge with a data cartridge.
17 Read Only
Format
Warning The type of tape currently loaded into the drive is Read
Only on the SDLT tape drive.
19 Nearing Media
Life
Warning The data cartridge is nearing the end of its useful life.
You should use another data cartridge for your next
backup. Store this data cartridge in a safe place in case
you need to restore data from it.
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Verwandte Produkte und Handbücher für Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Betriebsanweisung
(160 Seiten)
(160 Seiten)
Software Quantum SuperLoader Betriebsanweisung
(196 Seiten)
(196 Seiten)
Software Quantum Scalar i2000 Betriebsanweisung
(544 Seiten)
(544 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern