Quantum 1200 Series DAT Autochanger Betriebsanweisung Seite 251
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-209
Table 4-122. REPORT SUPPORTED OPERATION CODES Command Descriptor Block — Field
Descriptions
Field Description
Service
Action
A service action of 0Ch identifies this as the REPORT SUPPORTED OPERATION
CODES command.
Reporting
Options
Specifies the type of information to be returned in the parameter data. All values other than
those listed are reserved.
Value Description
000b The drive returns a list of all supported operation codes and service actions in the
all_commands parameter data format. The drive ignores any values in the
Requested Operation Code and Requested Service Action fields. See
“All_commands Parameter Data Format” on page 4-210 for more information.
001b The drive returns the command support data in the one_command parameter data
format for the operation code specified in the Requested Operation Code field.
The drive ignores any value in the Requested Service Action field. If the
Requested Operation Code field specifies an operation code that has service
actions, the drive returns CHECK CONDITION status, Sense Key set to
ILLEGAL REQUEST, and Addition Sense Code set to INVALID FIELD IN
CDB. See “One_command Parameter Data Format” on page 4-212 for more
information.
010b The drive returns the command support data in the one_command parameter data
format for the operation code and service action specified in the Requested
Operation Code and Requested Service Action fields. If the Requested Operation
Code field specifies an operation code that does not have service actions, the
drive returns CHECK CONDITION status, Sense Key set to ILLEGAL
REQUEST, and Addition Sense Code set to INVALID FIELD IN CDB. See
“One_command Parameter Data Format” on page 4-212 for more information.
Requested
Operation
Code
Specifies the operation code of the command to be returned in the one_command
parameter data format. See “One_command Parameter Data Format” on page 4-212 for
more information.
Requested
Service
Action
Specifies the service action of the command to be returned in the one_command parameter
data format. See “One_command Parameter Data Format” on page 4-212 for more
information.
Allocation
Length
Specifies the number of bytes allocated for the returned parameter data. If the Allocation
Length value is not large enough to hold all of the parameter data, the drive truncates the
data it returns. This is not considered an error. The actual length of the parameter data is
available in the Additional Length field in the parameter data. If the remainder of the
parameter data is required, the application client must send a new REPORT SUPPORTED
OPERATION CODES command with an Allocation Length field value large enough to
hold all of the data.
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Verwandte Produkte und Handbücher für Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Betriebsanweisung
(160 Seiten)
(160 Seiten)
Software Quantum SuperLoader Betriebsanweisung
(196 Seiten)
(196 Seiten)
Software Quantum Scalar i2000 Betriebsanweisung
(544 Seiten)
(544 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern