Quantum LTO 4 Betriebsanweisung Seite 31
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 2 Installation Procedures
Installing the Internal LTO-4 (Model B) Half-Height Tape Drive
LTO-4 (Model B) Half-Height Tape Drive User’s Guide 15
• Attach the internal SCSI interface cable to the 68-pin
parallel SCSI connector on the back of the drive.
Caution: The LTO-4 (Model B) Half-Height Tape Drive with
the parallel SCSI interface is a low voltage
differential (Ultra320 SCSI) SCSI device. Install it
only in LVD environments. Plugging an LVD drive
into a high voltage differential (HVD) bus makes
the entire bus nonfunctional and may permanently
damage the drive or other SCSI devices on the bus.
• See the internal parallel SCSI bus termination examples in
figure 3
on page 11 to check/verify the system SCSI bus
configuration and install a 68-pin Ultra320 SCSI bus
terminator, as required.
b For the SAS internal drive, attach the internal SAS interface
cable to the 29-pin SFF-8482 SAS connector on the back of the
drive.
3 If you are installing the internal LTO-4 (Model B) Half-Height Tape
Drive in a tape library system, connect the RS-422 serial interface
cable to the serial library port on the back of the drive. (The serial
library port is not used on workstation or server systems.)
4 Connect the internal drive DC power cable to the DC power
connector on the back of the drive.
5 Reinstall the system cover.
6 Reconnect the system AC power cord to the facility AC power
receptacle.
After connecting the internal drive interface and DC power cables,
proceed to Restarting the Internal Tape Drive System
in the following
subsection.
Restarting the Internal
Tape Drive System
After connecting the internal drive interface and DC power cables:
1 Restart the workstation or server system.
2 Refer to the operating procedures in chapter 3
to verify that the
internal LTO-4 (Model B) Half-Height Tape Drive comes on and
completes the Power On Self Test (POST) functions.
- LTO-4 (Model B) 1
- Contents 3
- Chapter 3 Operation 25 4
- Chapter 4 Theory 35 4
- Chapter 5 Specifications 43 4
- Index 81 6
- Standards Conformance 13
- (Corporate Headquarters) 14
- Technical Publications 15
- Quantum Home Page 15
- Getting More 15
- Information or Help 15
- Worldwide End-User 16
- Product Warranty 16
- Introduction 17
- Drive Models 18
- Features 19
- Chapter 1 Introduction 20
- Installation Procedures 21
- Handling Precautions 22
- Guidelines 22
- Preinstallation 23
- Requirements 23
- Ta p e D r i v e 24
- Configuring the 25
- Internal Parallel SCSI 25
- Ta p e Drive 25
- ID Configuration Jumper Pins 26
- Bus Termination Examples 27
- Mounting the Internal 28
- Connecting the Internal 29
- Drive Interface and DC 29
- Power Cables 29
- DC power connector 30
- 68-pin SCSI cable 30
- 29-pin SFF-8482 SAS connector 30
- Restarting the Internal 31
- Tape Drive System 31
- Tabletop Parallel SCSI 33
- Connecting the 34
- Tabletop Drive Interface 34
- AC power connector 35
- AC power switch 35
- Restarting the Tabletop 38
- Drive System 38
- Operation 41
- Chapter 3 Operation 42
- Table 2 Front Panel Display 44
- LED Blink Codes 44
- Using LTO Tape Cartridges 46
- Write Protecting a Tape 47
- Cartridge 47
- Tape Cartridge Care and 48
- Maintenance 48
- Cleaning the Tape Drive 49
- Chapter 4 51
- Track Layout 51
- Chapter 4 Theory 52
- Recording Method 53
- Data Buffer 53
- Data Integrity 53
- Error-correction Code 54
- Data Compression 55
- Considerations 56
- Intelligent Data 57
- Compression 57
- Specifications 59
- TO CARTRIDGE CENTER 60
- FROM BOTTOM MOUNTING SURFACE 60
- FROM SIDE MOUNTING SURFACE 60
- Power Specifications 61
- Chapter 5 Specifications 62
- Table 5 Power Dissipation 62
- Table 6 Drive Performance 63
- Environmental Requirements 64
- Injected Noise Specifications 65
- Reliability Specifications 65
- Mean Time Between 66
- Failures 66
- LTO Cartridge Specifications 67
- Troubleshooting Guide 69
- Troubleshooting Suggestions 70
- Computer Hardware 71
- Does Not Recognize the 71
- Computer Software 72
- Does Not Recognized 72
- Slow Backup 73
- Operations 73
- Failed Operations 76
- TapeAlert Messages 76
- Understanding LED Sequences 82
- Table 10 Tape Drive LED 83
- Sequences 83
- Installation Checklists 87
- Appendix B 91
- Equipment 91
- Appendix C 93
- Regulatory Compliances 93
- Safety Compliances 93
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum LTO 4
Bandlaufwerke Quantum DLT 7000 Handbuch
(312 Seiten)
(312 Seiten)
Bandlaufwerke Quantum DLT 2500 Handbuch
(12 Seiten)
(12 Seiten)
Bandlaufwerke Quantum DLT 4000 Handbuch
(300 Seiten)
(300 Seiten)
Bandlaufwerke Quantum LTO-2 Spezifikationen
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern