Quantum LTO 4 Betriebsanweisung Seite 84
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 6 Troubleshooting Guide
Understanding LED Sequences
68 LTO-4 (Model B) Half-Height Tape Drive User’s Guide
Ready is OFF,
others are ON
Firmware is being
reprogrammed.
None. Do not reset or power cycle the drive.
Clean FLASHES
The drive requires cleaning. Load the Ultrium cleaning cartridge, see
Cleaning the Tape Drive
on page 33.
If the Clean LED is still flashing when you load
a new or known good data cartridge after
cleaning, call for service.
Ready FLASHES
and Clean is ON
Cleaning is in progress. None. The cleaning cartridge will eject on
completion.
The cleaning cycle can take up to 5 minutes to
complete.
Tap e F L A S H E S
The drive believes the current
tape or the tape just ejected is
faulty.
Unload the tape cartridge. Make sure that you
are using the correct format cartridge; an
Ultrium data cartridge or Ultrium Universal
Cleaning Cartridge.
Reload the cartridge. If the Tap e L E D still
flashes or starts flashing during the next
backup, load a new or known good cartridge.
If the Tap e L E D is now off, discard the 'suspect'
tape cartridge. If it is still on, call for service.
The tape is
ejected
immediately and
Tap e F L A S H E S , or
Drive FLASHES on
unloading tape.
The tape cartridge memory
(CM) may be faulty.
Write protect the cartridge by sliding the
switch on the tape cartridge, see Cleaning the
Tap e D r i v e on page 33. The tape can be loaded
and the data read. Once the data is recovered,
the cartridge must be discarded.
LED Sequence
(Half-Height) Cause Action Required
- LTO-4 (Model B) 1
- Contents 3
- Chapter 3 Operation 25 4
- Chapter 4 Theory 35 4
- Chapter 5 Specifications 43 4
- Index 81 6
- Standards Conformance 13
- (Corporate Headquarters) 14
- Technical Publications 15
- Quantum Home Page 15
- Getting More 15
- Information or Help 15
- Worldwide End-User 16
- Product Warranty 16
- Introduction 17
- Drive Models 18
- Features 19
- Chapter 1 Introduction 20
- Installation Procedures 21
- Handling Precautions 22
- Guidelines 22
- Preinstallation 23
- Requirements 23
- Ta p e D r i v e 24
- Configuring the 25
- Internal Parallel SCSI 25
- Ta p e Drive 25
- ID Configuration Jumper Pins 26
- Bus Termination Examples 27
- Mounting the Internal 28
- Connecting the Internal 29
- Drive Interface and DC 29
- Power Cables 29
- DC power connector 30
- 68-pin SCSI cable 30
- 29-pin SFF-8482 SAS connector 30
- Restarting the Internal 31
- Tape Drive System 31
- Tabletop Parallel SCSI 33
- Connecting the 34
- Tabletop Drive Interface 34
- AC power connector 35
- AC power switch 35
- Restarting the Tabletop 38
- Drive System 38
- Operation 41
- Chapter 3 Operation 42
- Table 2 Front Panel Display 44
- LED Blink Codes 44
- Using LTO Tape Cartridges 46
- Write Protecting a Tape 47
- Cartridge 47
- Tape Cartridge Care and 48
- Maintenance 48
- Cleaning the Tape Drive 49
- Chapter 4 51
- Track Layout 51
- Chapter 4 Theory 52
- Recording Method 53
- Data Buffer 53
- Data Integrity 53
- Error-correction Code 54
- Data Compression 55
- Considerations 56
- Intelligent Data 57
- Compression 57
- Specifications 59
- TO CARTRIDGE CENTER 60
- FROM BOTTOM MOUNTING SURFACE 60
- FROM SIDE MOUNTING SURFACE 60
- Power Specifications 61
- Chapter 5 Specifications 62
- Table 5 Power Dissipation 62
- Table 6 Drive Performance 63
- Environmental Requirements 64
- Injected Noise Specifications 65
- Reliability Specifications 65
- Mean Time Between 66
- Failures 66
- LTO Cartridge Specifications 67
- Troubleshooting Guide 69
- Troubleshooting Suggestions 70
- Computer Hardware 71
- Does Not Recognize the 71
- Computer Software 72
- Does Not Recognized 72
- Slow Backup 73
- Operations 73
- Failed Operations 76
- TapeAlert Messages 76
- Understanding LED Sequences 82
- Table 10 Tape Drive LED 83
- Sequences 83
- Installation Checklists 87
- Appendix B 91
- Equipment 91
- Appendix C 93
- Regulatory Compliances 93
- Safety Compliances 93
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum LTO 4
Bandlaufwerke Quantum DLT 7000 Handbuch
(312 Seiten)
(312 Seiten)
Bandlaufwerke Quantum DLT 2500 Handbuch
(12 Seiten)
(12 Seiten)
Bandlaufwerke Quantum DLT 4000 Handbuch
(300 Seiten)
(300 Seiten)
Bandlaufwerke Quantum LTO-2 Spezifikationen
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.456 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern