Quantum LTO 4 Betriebsanweisung Seite 88
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix A Installation Checklists
Tabletop LTO-4 (Model B) Half-Height Tape Drive Quick Start
72 LTO-4 (Model B) Half-Height Tape Drive User’s Guide
Tabletop LTO-4 (Model B) Half-Height Tape Drive Quick
Start
Use the following quick-start procedure to install tabletop LTO-4 (Model
B) Half-Height Tape Drive. Print this page and check each step as you
complete it. If you need more information about a step, see the
subsection referenced in the step.
q 3 Connect a serial-attached SCSI (SAS) interface cable to the drive.
See Connecting the Internal Drive Interface and DC Power Cables
on page 13.
q 4 Connect a serial cable, if installing the tape drive in a tape library system.
See Connecting the Internal Drive Interface and DC Power Cables
on page 13.
q 5 Connect a DC power cable to the drive.
See Connecting the Internal Drive Interface and DC Power Cables
on page 13.
q 6 Replace the computer covers and AC power cable, turn on the computer, and
verify that the internal tape drive is operating properly.
q 7 Register your tape drive.
See Registering the LTO-4 (Model B) Half-Height Tape Drive
on page 23.
q 1 Unpack the contents of your drive package, and check for damaged items.
See Unpacking and Inspecting the Drive
on page 8.
q 2 Connect a serial-attached SCSI (SAS) interface cable to the drive.
See Connecting the Internal Drive Interface and DC Power Cables
on page 13.
q 3 Connect a power cable to the drive.
See Connecting the Tabletop Drive Interface and AC Power Cables
on page 18.
- LTO-4 (Model B) 1
- Contents 3
- Chapter 3 Operation 25 4
- Chapter 4 Theory 35 4
- Chapter 5 Specifications 43 4
- Index 81 6
- Standards Conformance 13
- (Corporate Headquarters) 14
- Technical Publications 15
- Quantum Home Page 15
- Getting More 15
- Information or Help 15
- Worldwide End-User 16
- Product Warranty 16
- Introduction 17
- Drive Models 18
- Features 19
- Chapter 1 Introduction 20
- Installation Procedures 21
- Handling Precautions 22
- Guidelines 22
- Preinstallation 23
- Requirements 23
- Ta p e D r i v e 24
- Configuring the 25
- Internal Parallel SCSI 25
- Ta p e Drive 25
- ID Configuration Jumper Pins 26
- Bus Termination Examples 27
- Mounting the Internal 28
- Connecting the Internal 29
- Drive Interface and DC 29
- Power Cables 29
- DC power connector 30
- 68-pin SCSI cable 30
- 29-pin SFF-8482 SAS connector 30
- Restarting the Internal 31
- Tape Drive System 31
- Tabletop Parallel SCSI 33
- Connecting the 34
- Tabletop Drive Interface 34
- AC power connector 35
- AC power switch 35
- Restarting the Tabletop 38
- Drive System 38
- Operation 41
- Chapter 3 Operation 42
- Table 2 Front Panel Display 44
- LED Blink Codes 44
- Using LTO Tape Cartridges 46
- Write Protecting a Tape 47
- Cartridge 47
- Tape Cartridge Care and 48
- Maintenance 48
- Cleaning the Tape Drive 49
- Chapter 4 51
- Track Layout 51
- Chapter 4 Theory 52
- Recording Method 53
- Data Buffer 53
- Data Integrity 53
- Error-correction Code 54
- Data Compression 55
- Considerations 56
- Intelligent Data 57
- Compression 57
- Specifications 59
- TO CARTRIDGE CENTER 60
- FROM BOTTOM MOUNTING SURFACE 60
- FROM SIDE MOUNTING SURFACE 60
- Power Specifications 61
- Chapter 5 Specifications 62
- Table 5 Power Dissipation 62
- Table 6 Drive Performance 63
- Environmental Requirements 64
- Injected Noise Specifications 65
- Reliability Specifications 65
- Mean Time Between 66
- Failures 66
- LTO Cartridge Specifications 67
- Troubleshooting Guide 69
- Troubleshooting Suggestions 70
- Computer Hardware 71
- Does Not Recognize the 71
- Computer Software 72
- Does Not Recognized 72
- Slow Backup 73
- Operations 73
- Failed Operations 76
- TapeAlert Messages 76
- Understanding LED Sequences 82
- Table 10 Tape Drive LED 83
- Sequences 83
- Installation Checklists 87
- Appendix B 91
- Equipment 91
- Appendix C 93
- Regulatory Compliances 93
- Safety Compliances 93
Verwandte Produkte und Handbücher für Bandlaufwerke Quantum LTO 4
Bandlaufwerke Quantum DLT 7000 Handbuch
(312 Seiten)
(312 Seiten)
Bandlaufwerke Quantum DLT 2500 Handbuch
(12 Seiten)
(12 Seiten)
Bandlaufwerke Quantum DLT 4000 Handbuch
(300 Seiten)
(300 Seiten)
Bandlaufwerke Quantum LTO-2 Spezifikationen
(1 Seiten)
(1 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern